Table of Contents
How big of a tire can a Dana 35 handle?
They can and will break at any time, don’t push your luck with tires bigger than 31″. The front can handle 35’s just fine but over that and it needs attention. 2.5L Genius of some sort.
Can a Dana 30 Handle 35 inch tires?
Brian, there is no definitive rule of thumb when it comes to running 35-inch tires under a JK with a Dana 30 front axle. Yes, you may twist your axle housing or explode the carrier running 35s, but you could do just the same running 33s.
Can you make a Dana 35 strong?
There are two options when upgrading the 35 shafts. Superior Axle & Gear offers its Super 35 kit and Warn has a full-float kit. The Super 35 kit is available for both C-clip and non-C-clip axles. The kit replaces the smallish shafts with 1.31-inch 30-spline pieces that are over 35 percent stronger than stock.
Are all Dana 35 axles the same?
Any Wrangler Dana 35c axle shaft from ’91 or ’92 to ’06 will fit. Before that, they were non-c-clip designs. The two sides have slightly different lengths so make sure you get them in the right sides. -When you have a choice, buy American.
How big of a tire can you run on Dana 30?
The stock Dana 30 is fine up to the 35″ tire size. Depending on the difficulty of the trails you do and whether your front axle has a locker, hardened axle shafts may be required but other than that, life with 35″ tires on a Dana 30 is absolutely fine.
What gear ratio is a Dana 35?
The Dana 35 is used extensively in the Jeep models. This axle had a GAWR up to 2700 lbs….Available Gear Ratios.
| Ratio:1 | Pinion:Ring Teeth |
|---|---|
| 3.07 | 14:43 |
| 3.08 | 13:40 |
| 3.31 | 13:43 |
| 3.54 | 13:46 |
Is AMC 35 the same as Dana 35?
The AMC Model 35 Axle, also known as the AMC 35, M35, Jeep Model 35, and Dana 35 axle can be found under older AMC cars, several older and current Jeeps, as well as some Ford and Doge SUVs. It features an 7.560″ diameter ring gear (7.790″ in Jeep WJ Cherokee versions) with 27 spline semi-floating axle shafts.
What gearing is a Dana 35?
The Dana/Spicer Model 35 is an automotive axle manufactured by Dana Holding Corporation since 1985 when American Motors (AMC) sold its axle tooling equipment to Dana. The axle was originally named an AMC-15 when it was first made in 1962….Available Gear Ratios.
| Ratio:1 | Pinion:Ring Teeth |
|---|---|
| 3.31 | 13:43 |
| 3.54 | 13:46 |
| 3.58 | 12:43 |
What uses a Dana 35?
The most common Dana 35 applications are as a rear axle in the Jeep Cherokee, Jeep Wrangler, and Jeep Comanche and as a front axle in the Ford Explorer and Ford Ranger. It is “reliable in day-to-day street use, but notoriously the opposite when worked hard.”
What size tires can I put on Dana 30?
How big are the tubes on a Dana 35 axle?
The tubes measure 2.6 inches thick which is pretty small. The Chrysler 8.25 has a three-inch tube diameter, so keep that in mind if you upgrade your rear axle. Last but certainly not least: the axle shafts. The Dana 35 axle shafts have 27 splines and a 1.18-inch diameter.
What is the difference between a Dana 35 and a 44?
The Dana 44 axle shafts have 30 splines and a 1.31-inch diameter. It may not sound like a big difference, but it’s actually a pretty big. Although the Dana 44 has a larger differential, and stronger axle shafts, it shares the same weak axle tubes with the Dana 35.
What is the difference between a Dana 35 and Chrysler 825?
The Chrysler 8.25 has a three-inch tube diameter, so keep that in mind if you upgrade your rear axle. Last but certainly not least: the axle shafts. The Dana 35 axle shafts have 27 splines and a 1.18-inch diameter.
Is the Dana 35 good for off-roading?
The Dana 35 has earned a pretty poor reputation in the off-road world. We can totally understand this because we have personally had a D35 explode on us from just being daily driven with 31-inch tires. In our case, the spider gears would no longer properly mesh together.