Does OSHA require table saw guards?
Each circular crosscut table saw shall be guarded by a hood which shall meet all the requirements of paragraph (c)(1) of this section for hoods for circular ripsaws. Circular resaws. Each circular resaw shall be guarded by a hood or shield of metal above the saw.
How many teeth should a table saw have?
Typically made with 24 to 30 wide teeth, ripping blades are designed to help you quick tear through natural wood materials. Here are a few ways you might use a ripping blade: To cut a single piece of lumber in half or in separate portion. To cut many pieces of natural wood to size before making more precise cuts.
What are the safety features on a table saw?
Table Saw Safety Features (Woodworking)
- Riving Knife & Splitter.
- Anti-Kickback Pawls.
- Push Stick.
- Blade Guard.
- Magnetic switch.
- Sensors.
When should you not use a fence on a table saw?
Never use it as a cut off gauge. Use a push stick when ripping narrow or short stock (e.g., when the fence is set less than about 15 cm (6 in) from the blade; when the piece is less than 30 cm (12 in) long or when the last 30 cm (12 in) of a longer piece is being cut).
What should you not do with a table saw?
When using a table saw, the woodworker should never attempt a free-hand cut. Instead, use the fence or miter gauge to guide the stock. However, keep in mind that the fence and miter gauge should never be used together, as the end grain of a piece of stock can bind against the fence.
What is the OSHA general duty clause 1910?
The OSHA General Duty Clause, Section 5(a)(1) of the Occupational Safety and Health Act, requires that each employer furnish to each of its employees a workplace that is free from recognized hazards that are causing or likely to cause death or serious physical harm.
Which side of table saw should you stand on?
The best place to stand when you are using a table saw is to the left of the saw blade in a position that is natural and comfortable for you. Standing away from the direct line of the blade is important for safety. If you stand to the left, you’ll automatically position the blade between you and the fence.
Can you use table saw without fence?
Just attach a short strip of wood slightly thinner than the width of the rip cut to the end of a 4-ft. 1×6. Then hold the board against it and push the jig through. The jig keeps your hands well away from the blade, and you can rip as many pieces as you need without ever moving the fence.
What are the four elements that must be present to prove a violation under the General Duty Clause?
The following elements are necessary to prove a violation of the General Duty Clause:
- The employer failed to keep the workplace free of a hazard to which employees of that employer were exposed;
- The hazard was recognized;
- The hazard was causing or was likely to cause death orserious physical harm; and.
Do Diablo blades last longer?
In fact, anytime I buy a new saw, the first thing I do is get rid of the manufacturer blade and install a Diablo blade. Diablo blades always seem to stay sharper longer, which means they last longer, which means in the end, they can be priced lower than other brands.
What is a table table saw used for?
Table saws are used for straight sawing. Depending on the blade, they cut either across (crosscut) or with (ripsaw) the grain of the wood. With hand-fed saws, the operator adjusts the height and angle of the blade. Then, holding the stock, the operator pushes it into the blade.
What are the most common injuries when operating a table saw?
Injuries can occur if an operator’s hands slip while feeding the stock into the saw, or if the operator holds his or her hands too close to the blades while cutting. The operator can also be injured when removing scrap or finished pieces of stock from the table.
What is a self feed table saw used for?
Self-feed or power table saws are equipped with rollers or a conveyor system to hold the lumber and force-feed it into the saw blade. Injuries can occur if an operator’s hands slip while feeding the stock into the saw, or if the operator holds his or her hands too close to the blades while cutting.
How do you stop a table saw from coasting?
Attach a brake to the motor’s arbor to stop the saw from coasting after the power has been cut off, or have the operator remain at the saw station after the motor is shut off, until the blade stops turning. A worker was ripping a wooden workpiece with a dado on a manual-feed table rip saw.