How does Whirlpool auto sensing work?
If the water level seems too low, or if the washer does not fill completely, auto-sensing helps stabilize the amount of water used. The washer senses the size of the load and adds the correct amount of water for the load size. You may notice during a cycle that the wash load is not completely submerged in water.
How long should Whirlpool washer be in sensing mode?
A Whirlpool washer should only stay in the sensing stage for 2-3 minutes. When it gets stuck on sensing, it’s likely because of a faulty water inlet valve, shift actuator, drive motor, or main control board. A fault at any of those parts can prevent the washer from advancing past the sensing stage.
What does auto sensing mean?
Autosense refers to a feature found in network adapters that allows them to automatically recognize the current local network’s speed and adjust its own setting accordingly. It is often used with Ethernet, fast Ethernet, switches, hubs and network interface cards.
How do I make my Whirlpool Cabrio spin?
Try this method ” select the RINSE/DRAIN & SPIN cycle and deselect the EXTRA RINSE option. In this case it cancels ALL rinsing for the cycle. This is how you get a spin-only cycle.”
How do you bypass a washing machine sensing?
Quick Water Level Bypassing Formula For Washing Machine
- Let us say you have 2 lbs of clothes.
- Add the 2 lbs of clothes in the washtub.
- Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric.
- Start the wash cycle.
- You have successfully bypassed water level sensor.
Why does my Whirlpool washer keep saying sensing?
Quick Note: During auto sensing, your washer usually senses if the load size is correct as well as balance so ensure you have not overloaded it and that the machine is properly balanced.
How do I test a Whirlpool Cabrio washing machine?
Console & Indicator Diagnostic Test Mode
- The washing machine should be in standby (off) mode.
- Press and release the following buttons within 4 seconds.
- if successful “dt” should display on the washing machines indicator.
- Within 5 seconds press “Start” all indicator lights should come on and 88 should be displayed.
How do I bypass Whirlpool sensing?
Here is a simple way to do this:
- Let us say you have 2 lbs of clothes.
- Add the 2 lbs of clothes in the washtub.
- Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric.
- Start the wash cycle.
- You have successfully bypassed water level sensor.
What is the diagnostic test on a whirlpool Cabrio washing machine?
The Console and indicator diagnostic test on a Whirlpool Cabrio washing machine is used to check the cycle selector knob, console indicators, user interface buttons, two-digit display, and beeper. 1. The washing machine should be in standby (off) mode. 2. Press and release the following buttons within 4 seconds.
How do you use the recirculation pump on a whirlpool Cabrio washing machine?
To manually activate the Recirculation pump on the Whirlpool Cabrio washing machines press and release the “Clean Washer” or “Drain & Spin” button (push button models) or Select the “Clean Washer” or “Drain & Spin” cycle option and press start (rotary knob models).
What should I do if my Cabrio washer does not agitate?
If the washing machine does not agitate go to manual diagnostic mode: motor, agitate. The Cabrio Washer’s recirculation pump will energize for 10 seconds, spraying water back into the wash tub from the back left of the washer. If no water is being re-circulated go to manual diagnostic mode: Pumps.
How do I check if my Cabrio Washer has a fabric softener?
If your washing machine has a fabric softener dispenser and no water flows go to manual diagnostic mode: Water valves. The Cabrio Washer’s hot and cold (Warm Water) primary water valves open as well as the detergent water valve for 10 seconds If no water flows through the detergent cup go to manual diagnostic mode: Water valves