What is a ifconfig network?
The “ifconfig” command is used for displaying current network configuration information, setting up an ip address, netmask, or broadcast address to a network interface, creating an alias for the network interface, setting up hardware address, and enable or disable network interfaces.
How do I find my interface name in Terminal?
To do this, simply open a terminal and type “ifconfig -a”. This will return a list of all available network interfaces on your system. You can append the name of the interface to the end of the command (e.g. “ifconfig eth0”) to view information about a specific interface.
What is the difference between ipconfig and ifconfig?
Functionality: The ipconfig command displays all the currently connected network interfaces whether they are active or not. On the other hand, the ifconfig command displays only the enabled network interfaces that are connected to the system.
What is the output of ifconfig?
Nevertheless, the ifconfig output shows that three forms of addresses are currently assigned to qfe0: loopback (lo0), IPv4 (inet), and IPv6 (inet6). In the IPv6 section of the output, note that the line for interface qfe0 displays the link-local IPv6 address. The second address for qfe0 is displayed on the qfe0:1 line.
Why ifconfig is not working?
If you tried to install the ifconfig utility and failed, it’s because ifconfig cannot be individually installed. It is included with the net-tools package. To be able to use the ifconfig command, you have to install the net-tools package first.
How do I know my network interface?
Follow these steps to check on the NIC hardware:
- Open the Control Panel.
- Open the Device Manager.
- Expand the Network Adapters item to view all network adapters installed on your PC.
- Double-click the Network Adapter entry to display your PC’s network adapter’s Properties dialog box.
How do I list network interfaces?
You can use the ifconfig command to list the network interfaces available in your system. Instead of typing ifconfig, type the command /sbin/ifconfig to list the network interfaces in your system.
Why do we use ifconfig?
ifconfig is used to configure the system’s kernel-resident network interfaces. It is used at boot time to set up interfaces as necessary. After that, it is usually only needed when debugging, or when system tuning is needed. If no arguments are given, ifconfig displays the status of the system’s active interfaces.
Why is ifconfig important?
What is the IP address in ifconfig?
Typically, ifconfig can only be used under a superuser account in your terminal. A list of all your network interfaces will appear. Following the heading of the interface whose IP address you’re searching for, you will see a “inet addr:” section containing your IP address.
Where did ifconfig go?
Following some improvements in the kernel and the gradual move to driving network things via netlink; ifconfig has been largely replaced by the ip command. This is the main command that would be used in place of ifconfig. It will just display the IP addresses assigned to all interfaces.
What package has ifconfig?
net-tools package
If you still prefer to use ifconfig as part of your daily sysadmin routine, you can easily install ifconfig as part of the net-tools package.
How do I know which network adapter is mine?
It is also known as a network interface card (NIC).
- Right-click My Computer, click Properties, click the Hardware tab, and then click Device Manager.
- Double-click Network adapters, and then verify that the correct network adapter name is selected.
What is the use of ifconfig command?
The “ ifconfig ” command is used for displaying current network configuration information, setting up an ip address, netmask, or broadcast address to a network interface, creating an alias for the network interface, setting up hardware address, and enable or disable network interfaces.
How to configure additional network interfaces using the ifconfig utility?
The ifconfig utility allows you to configure additional network interfaces using the alias feature. To add the alias network interface of eth0, use the following command. Please note that the alias network address is in the same subnet mask.
What does ifconfig eth0 down do?
The “ down ” or “ ifdown ” flag with interface name ( eth0) deactivates the specified network interface. For example, “ ifconfig eth0 down ” or “ ifdown eth0 ” command deactivates the eth0 interface, if it is in active state.
What happens to ifconfig parameters when I restart the system?
Tip: Parameters that you set by using the ifconfig command are lost the next time that you restart your system. Use the chdev command to change the Object Data Manager (ODM) database for each interface to make parameter changes permanent.