What frequency does PetSafe wireless fence use?
The wireless dog and pet fence uses constant 18 kHz radio frequency in a circular area up to 1/2 acre and 180 feet in diameter to keep your pet within your set boundaries. The PetSafe wireless system comes complete with everything you need for quick and efficient training of your pet 6 months or older.
How do I sync my PetSafe wireless transmitter collar?
Put boundary switch on transmitter in the ‘high’ position. Turn the boundary control dial on the transmitter to position 4. Standing within 1.5 – 3 metres of the transmitter, re-insert the batteries into the receiver collar(s). Test the boundary by walking out into the safe zone until your receiver responds.
How do I know what frequency my Invisible Fence is?
How to Find Buried Invisible Fencing
- Make sure your invisible fence is plugged in and turned on. You should see an indicator light on the radio transmitter unit confirming this.
- Find the radio frequency that your invisible fence is using.
- Walk through your yard with the AM radio tuned to the correct radio frequency.
How do I adjust the frequency on my Invisible Fence?
Take off the back panel of the remote and/or transmitter (some units come with both a walkie-talkie-looking transmitter plus a remote button). Search the back panels for any option to change the frequency.
How do I reset my PetSafe transmitter?
Make sure the collar is powered on. Press and hold the button on the collar until a beep is heard and the light flashes green to turn the collar on. Press and hold the power button for 10 seconds to reset the collar. The light turns red and the collar turns off.
Why is my PetSafe wireless transmitter not working?
When troubleshooting problems with a PetSafe transmitter, start by replacing the battery. More often than not, transmitter issues are just due to lack of power. On most models, the test light should tell you if power is low.
How do I increase the voltage on my Invisible Fence?
How to Change the Strength of an Invisible Fence
- Push the button on the receiver. A light on the receiver will flash.
- Adjust the distance from the boundary wire to trigger a warning alarm. Most transmitter boxes have a knob or lever to use to change the distance.
- Change the metal prongs on the receiver.
Can Invisible Fence interfere with WiFi?
However, if you use an invisible boundary to cover your entire yard and your home WiFi is on the other side of the house, then you might experience some issues because the dog fence signal can interfere with WiFi.
Can you change the frequency on an Invisible Fence collar?
Take off the back panel of the remote and/or transmitter (some units come with both a walkie-talkie-looking transmitter plus a remote button). Search the back panels for any option to change the frequency. In the old days, there were actual analog dials that you could move up and down to change the frequency.
How do I reset my petsafe wireless fence collar?
Press and hold the button on the collar until a beep is heard and the light flashes green to turn the collar on. Press and hold the power button for 10 seconds to reset the collar. The light turns red and the collar turns off. Continue holding the button.
Why is my PetSafe not working?
The light may come on and fade out. Place the battery back into the collar and twist to lock. Confirm that the collar powers on. If the collar does not power on, replace the battery with a new RFA-67 battery.
How do I reset my petsafe wireless transmitter?
Press and hold mode button on collar for 20 seconds. The light may come on and fade out. Place the battery back into the collar and twist to lock.
Can you adjust the voltage on an electric fence?
No. You cannot lower the voltage that simply. Your dogs will get used to it and stay away.
What is the voltage of an Invisible Fence?
These units are the only compatible 3-volt batteries authorized by Invisible Fence Brand to be used in your pet’s Computer Collar Receiver while under warranty.
Does the PetSafe in-ground dog fence transmitter work with all dog collars?
Ask here. The PetSafe In-Ground Dog Fence Transmitter is for All PetSafe or Pet Guardian Brand Dog Fences, it will work with any of the PetSafe or Pet Guardian brand dog fence collars except for the UltraSmart and YardMax collars. Works with ALL PetSafe and Pet Guardian Brand Dog Fence Collars except UltraSmart and YardMax Collars
What size wire do you use for dog fence transmitter?
Works with ALL PetSafe and Pet Guardian Brand Dog Fence Collars except UltraSmart and YardMax Collars We have two big dogs (about 95 lbs. each)and use this transmitter on around four to five acres. We installed the transmitter with 14 gauge wire and we were careful to follow the training directions.
Is Petsafe a good brand for in-ground dog fences?
We had another brand of in-ground dog fence, and it was terrible. We needed the stubborn dog, 9 volt collar offered by PetSafe so we switched to this system. It was easy to swap out the systems and switch collars. We’re very happy with it. Dog hasn’t left the yard once since we switched.
How many acres can the in-ground dog fence replacement transmitter enclose?
The PetSafe In-Ground Dog Fence Replacement Transmitter can enclose up to 10 acres which is approximately 3,200 feet of wire. Was this answer helpful? 19 of 19 Customer (s) found this Answer helpful.