Table of Contents
What is the difference between Flushmate 503 and 504?
Flushmate 503, 503H, and 504 Series Flushmate 503 series means it’s a 1.6 gallons per flush system. And lastly, 504 series means 1.0 GPF.
Should there be water in the tank with a Flushmate?
WHY IS THERE STANDING WATER INSIDE THE CHINA TANK? FLUSHMATE units can emit a few drops of water inside the tank during the flushing cycle. This water collects on the bottom of the china until the water level reaches the height of the built-in drain. Normal level of water is about 1-inch.
Why is my Flushmate keeps running?
A run-on condition may be caused by insufficient water pressure, an improperly adjusted Flush Valve Cartridge, or a clogged inlet screen. Refer to “Installation Requirements” for recommended minimum pressure.
Can I use flushmate in any toilet?
Flushmate Pressure Assist This change-out kit works only on a specific selection of tanks from other pressure-assisted toilets. According to Flushmate, its pressure-assisted system cannot be retrofitted into a standard, gravity-fed toilet.
Does flushmate work with any toilet?
A toilet equipped with FLUSHMATE® must be specifically designed to accommodate the effectiveness of FLUSHMATE®. FLUSHMATE® is NOT a retrofit product. The FLUSHMATE® system traps air and as it fills with water, it uses the water supply line pressure to compress the trapped air inside.
Can I replace flushmate with standard?
This Sloan Flushmate M-102540-F3A is the replacement tank for American-Standard 2045.013 one-piece toilets. This kit includes everything you need to easily replace your Flushmate system.
Why is my flushmate not flushing?
Inadequate water pressure, an improperly adjusted Flush Valve Cartridge, a clogged inlet screen, or insufficient air draw may cause a weak, sluggish, or no flush condition. Make sure that the water supply valve is fully open. Check for proper actuation adjustment, see Condition A-2, “Water runs and will not shut off.”
Can I replace Flushmate with standard?
Does Flushmate work with any toilet?
Can I install a Flushmate in my toilet?
Can I Install Flushmate® in my existing toilet? No! FLUSHMATE cannot be retrofitted to an existing gravity bowl. Bowls designed to work with FLUSHMATE harness the energy FLUSHMATE delivers to the bowl to create a “pushing” action for the waste.
Can you pour water in toilet tank to flush?
Simply fill the toilet tank with water until it reaches the top of the overflow tube. You can then flush your toilet with the flush handle as you normally would. There’s also another method to consider, which is referred to as a “gravity flush.” You’ll need to quickly pour about 1.6 gallons of water in the toilet bowl.
Is there a recall on the Flushmate 503 pressure assist system?
This recall is for Series 503 Flushmate III Pressure Assist flushing systems manufactured from October 1997 to February 2008. The units are rectangular, black, two-piece vessels made of injection molded plastic.
Are there any recalls on Flushmate toilet tanks?
This recall is for Series 503 Flushmate III Pressure Assist flushing systems installed inside toilet tanks that were manufactured from July 2009 through April 2011. The units are rectangular, black, two-piece vessels made of injection molded plastic. Previously recalled systems were manufactured from October 1997 through June 2009.
Where is the serial number on a Flushmate Flushmate 3?
The date code/serial number is 16 characters long and located on the label on the top of the Flushmate III. The first six numbers in the series are the date code. The date code range is October 14, 1997 (101497) through February 29, 2008 (022908).
How do I contact Flushmate about a recall?
Flushmate at (800) 303-5123 between 8 a.m. and 10 p.m. ET Monday through Friday and between 8 a.m. and 6:30 p.m. ET Saturday, or online at www.flushmate.com and click on “Flushmate III Recall” in the black box on the top left of the page for more information.