Can I replace rear shocks myself?
If you need to replace your car’s shock absorbers but don’t want to pay an expensive mechanic’s fee, you can do so on your own with a little effort. Shocks are essential to a car’s performance, giving it a smooth and even ride. Over time, however, the vehicle’s suspensions become worn out.
Can you change rear shocks without a jack?
To replace rear shocks you do not need to jack up the car.
How long does it take to replace shocks on a van?
around one to two hours
Typically, it takes around one to two hours to change struts, according to most professional mechanics.
Can you fit shock absorbers yourself?
Can I fit new shock absorbers myself? If you’re considering fitting new shock absorbers yourself, then you need to be an experienced and competent home mechanic. Park your car on a flat or level area—place chocks or wedges under the wheels that are going to stay on the ground.
How do you install rear shocks?
Connect the shock to the bottom shock mount. Then, compress the shock and work it into the top shock mount. Reinstall and finger-tighten the top bolt(s), and the bottom nut. Do It Right: Don’t torque these till the wheel is replaced and the vehicle is lowered so that the suspension is loaded.
Can I replace shocks and struts myself?
Installing New Shocks and Struts Once the old shocks and struts have been removed, you can simply replace the new ones. Make sure that you tighten all of the bolts securely. You will probably need a torque wrench to do this. Put the wheels back on the vehicle and you’re ready to test it out.
How much does it cost to replace rear shocks?
between $1,000 and $1,150
Replacing rear shocks will typically cost between $1,000 and $1,150. Unfortunately, those looking for a deal have very little wriggle room when it comes to this replacement. The parts for rear shock replacements cost roughly $900, while the labor costs for replacing rear shocks are typically around $200.
Can you compress a rear shock by hand?
You cannot judge the strength or condition of a shock/strut by hand movement alone. The force and speed generated by a vehicle in operation exceeds what you can accomplish by hand. The fluid valves are calibrated to operate differently depending on the degree of movement inertia which cannot be duplicated by hand.
What tools are needed to change shocks?
What tools do I need to change a shock absorber?
- Trolley jack.
- Axle stands.
- Sockets and spanner.
- Torque wrench.
- Coil spring compressor (if necessary)
How long does it take to fit rear shock absorbers?
How long does shock absorber replacement take? We’ve taken a look at some average times across the industry. Whether you’re replacing the front pair or the rear, the time taken is about the same—averaging between 1.5 and 4 hours.
Do you need special tools to install struts?
You’ll have to get an alignment done afterward (about $100), but you’ll still save about $300 by doing the job yourself. You’ll need rust penetrant, wrenches, a pin punch or large screwdriver, and a thin piece of plywood. You may need to buy a few large sockets and a breaker bar.
How do you remove rear shocks?
Start at the top by pulling it away from the shock mount. Then, push it away from the bottom shock mount. If you have trouble you may need to use a pry bar and mallet to loosen the shock. Do It Right: You may need to compress the shock to remove it from the vehicle.
Can you change rear shocks on a solid rear axle?
This shows you how to change your rear shocks on vehicles with a solid rear axle. Almost all vehicles are the same. Where I got my shocks: https://amzn.to/… This shows you how to change your rear shocks on vehicles with a solid rear axle. Almost all vehicles are the same.
How do you remove a rear shock mount from a car?
Start at the top by pulling it away from the shock mount. Then, push it away from the bottom shock mount. If you have trouble you may need to use a pry bar and mallet to loosen the shock. Do It Right: You may need to compress the shock to remove it from the vehicle.
Can I Change my shocks myself?
As they age, your steering and braking are affected, and the stability of your ride—as well as the condition of your tires—can deteriorate considerably. It’s recommended you have shocks and struts professionally inspected every fifty thousand miles. Fortunately, with a few tools, you can change shocks yourself.
Do you need to compress the shock absorbers before installing?
Do It Right: You may need to compress the shock to remove it from the vehicle. Before installing a new shock absorber it is recommended to manually pump them 3 to 5 times. When you do that, make sure the shock is oriented the way it will be in the vehicle, top side up.