What is the outside diameter of a 15/16 socket?
Impact 3/8″ Drive Deep Well Sockets Features:
| Item # | Diameter | Tip Outside Diameter |
|---|---|---|
| 1877476 | 9/16″ | 51/64″ / 20mm |
| 1877477 | 5/8″ | 15/16″ / 23.8mm |
| 1877478 | 11/16″ | 1-1/32″ / 26mm |
| 1877479 | 3/4″ | 1-1/16″ / 27mm |
What is the OD of a 7 8 socket?
SAE to Metric Conversion Chart
| SAE Size | Metric Size | Inches Decimal |
|---|---|---|
| 22mm | 0.866 | |
| 7/8″ | 0.875 | |
| 23mm | 0.906 | |
| 29/32″ | 0.906 |
What is the outside diameter of a 3/4 socket?
Common measurements are as follows: 1/4”(6.3mm), 3/8”(9.5mm), 1/2”(12.7mm), 3/4”(19.0mm) and 1”(25.4mm)。
What are the socket wrench sizes?
There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).
What is the OD of a 1/2 socket?
Impact 1/2″ Drive Deep Well Sockets Features:
| Item # | Diameter | Base Outside Diameter |
|---|---|---|
| 1882336 | 7/16″ | 61/64″ / 24mm |
| 1882337 | 1/2″ | 61/64″ / 24mm |
| 1882338 | 9/16″ | 61/64″ / 24mm |
| 1882339 | 5/8″ | 61/64″ / 24mm |
How do you measure socket size?
Look through the table’s decimal column and select the first decimal larger than your caliper reading. Select the corresponding fraction. The website Sizes has a table showing Imperial (American) socket sizes. If the fraction is listed, it’s the size of your nut and required socket.
What size bolt takes a 1 1 2 wrench?
US Bolt Head/Wrench Size
| Bolt Diameter | Head and Wrench Size | |
|---|---|---|
| Hex Bolt – Lag Bolt – Square Bolt | Heavy Hex Bolt | |
| 1″ | 1-1/2″ | 1-5/8″ |
| 1-1/8″ | 1-11/16″ | 1-3/4″ |
| 1-1/4″ | 1-7/8″ | 2″ |
What size bolt takes 1 1 8 wrench?
Hex Bolt, Lag Bolt, Square Bolt and Heavy Hex Bolt.
| US Bolts | ||
|---|---|---|
| Bolt Diameter (in) | Head and Wrench Size (in) | |
| 7/8 | 1 5/16 | 1 7/16 |
| 1 | 1 1/2 | 1 5/8 |
| 1 1/8 | 1 11/16 | 1 -3/4 |
What is the closest size metric wrench to a 1/2 wrench?
12.7 13
Convert between US Inches and metric mm wrench and spanner sizes.
| Standard SAE US Wrench/Spanner Size (inches) | Metric Wrench/Spanner Size (mm) |
|---|---|
| 1/2 | 12.7 |
| 13 | |
| 17/32 | 13.49 |
| 14 |
What are the standard socket sizes in order?
Six Point Standard Sockets (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1)
Are SAE and metric the same?
SAE sockets are sized in inches and fractions of inches. Metric and SAE wrenches have different systems of measurement. Metric sockets and wrenches use the metric measurement system. This is when millimeters are used to describe the size.
Are Nuts measured from the inside diameter?
Bolts commonly use four types of measurement, while nuts use only two. Bolts are measured in length of shank, bolt head size, width of shank (the diameter of the threaded bolt body) and the thread pitch (the size of the thread). Nuts are measured by the width of the hex shape and by their thread pitch.
How do you measure bolt socket size?
How to Determine the Right Size Socket for a Nut
- Turn on the digital caliper and set it to read in inches, not millimeters.
- Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides.
- Check the caliper display.
- Turn on the digital caliper and set it to read in millimeters, not inches.
What is nominal bolt diameter?
NOMINAL DIAMETER (NOMINAL BOLT DIAMETER) The diameter equal to the external diameter of the threads or the overall diameter of the part. (Nominal diameter is more of a label than a size. For example, a bolt and nut may be described as being ½” diameter.
Is SAE the same as imperial?
How to Convert Between SAE and Imperial Socket Sizes? There are two different methods for measuring the hex sizes of sockets. The SAE (Society of Automotive Engineers) system uses inches, and the imperial or metric system uses millimeters.
What is a 1/2 drive socket used for?
1/2” Drives: Usually in use for more substantial jobs on vehicles where the nuts are more substantial and need more torque. You find them in use for 19mm socket size and above. While you have a large number of metric and SAE standard socket sizes, you can have differing wrenches to use these.
What is the size of a 1 inch socket?
Convert: 1 inch = 25.4mm Sockets are available in deep, semi-deep and standard sizes. You can select the length most suitable for your working environment. The semi-deep size is designed specifically for 3/8″ DR.
What size socket do I need for a 5mm nut?
For example, you’ll require a 5mm socket for a 5mm nut. The size of the drive hole is determined by usage and torque demand. Common measurements are as follows: 1/4” (6.3mm), 3/8” (9.5mm), 1/2” (12.7mm), 3/4” (19.0mm) and 1” (25.4mm)。 Why use inch? Because this was developed in Great Britain during the Industrial Age.
What size socket do I need for a 3/8 drive?
Usually, you want to use with a socket size 12mm or smaller (but up to 14mm for low torque applications). 3/8″ Drive The most versatile and useful drive size for most people. Use it for engine work or all-purpose use around your home.