Table of Contents
What nails should I use for quarter round trim?
Attaching Quarter Round Because it’s finish trim, install quarter round with finish nails, which have smaller heads than standard nails. A finish nail gun, fitted with 1.5- or 2-inch finish nails, works well. You can also drive finish nails the old-fashioned way — with a hammer.
Where do you put nails in quarter round?
Choose finish nails that are long enough to penetrate the thickness of the quarter round molding and the drywall with enough left over to go at least 1/2 inch into the wall’s base plate. Place the nails no more than 18 inches apart for 3/4-inch molding.
How do you nail quarter round finish nails?
- Step 1: Cut molding.
- Step 2: Lay molding against wall, flush with the floor.
- Step 3: Hammer your finishing nail almost all the way into the wall.
- Step 4: Use the nail set to drive the nail the rest of the way in.
- Step 5: Finish with sealant.
- Step 6: Cover nail heads.
What is the difference between a brad nail and a finish nail?
Finish nails are stronger than brads, so choose them if your project needs to be durable. Brads are thin, 18-gauge nails made for more delicate woodworking jobs. They’re available in collated strips for nail guns or individual pieces. Brad nail length ranges from 1/2-inch to 2 1/2-inch.
How long should nails be for quarter round?
Most quarter round is installed with finish nails. To avoid having to use putty to fill in holes, some professionals do use brad nails. To install quarter round, use nails that are 1 1/4 to 2 inches in length, depending on the thickness of the material.
Can you use a hammer to nail quarter-round?
Hammer the nail through the quarter-round and into the baseboard with a hammer. The finishing nail is thin enough to not split the quarter-round and long enough to anchor the molding.
What nails do you use for molding?
The most common size used in moulding is 1-1/4″ (3d) or 1-1/2″ (4d) finishing nail. Select a galvanized or stainless steel nail for outdoor use.
Can I use a brad nailer for quarter-round?
If you’re doing lighter molding, such as quarter-round at the bottom of your wall, or installing a chair rail, an 18 Gauge Brad Nailer is fine for the job.
How do you hammer in quarter rounds?
How long should trim nails be?
So it’s best, before you begin the project, to be absolutely sure you’re using the right nail size for baseboards in your home. As a general rule, baseboard nails shouldn’t be any longer than 2 inches. The ideal length is between 1.5 inches and 2 inches.
What size nails do I use for trim?
· 15 & 16-gauge nails (finish nails) 15 and 16 gauge nails are the fattest nails you can use to attach trim (to be clear, 15 is thicker than 16). You shoot them with a finish nailer, a nail gun specifically designed for fastening finishing materials such as trim, crown molding, and more.
How to install quarter round molding?
The most common way to install quarter round molding is using nails. You can either do this manually or use a nail gun. Let’s start by looking at the manual method: Step 1: Sweep the dirt and debris off the wall. Ensure that the surface is clean, including the edges of the wall where the molding will be placed.
How to use a quarter round nail gun?
Kneel down next to your first piece of quarter round, holding the tip of the nail gun almost parallel to the floor, but with a slight downward tilt. 3. Nail Slightly at an Angle
What kind of Nailer do you use for quarter round molding?
You can also go a fancier route with all kinds of elaborate molding, but for the purpose of this tutorial I’m just using good old fashioned quarter round. Now, most tutorials you’ll find online will tell you to nail the molding in place with a pneumatic nailer.
How do you nail a quarter round to baseboard?
To nail a quarter round, hold a fastener from 2-inches of the edges just at the middle of molding. Alongside, try to point the nail parallelly with the floor. Now, hammer the nail until it reaches the baseboard, passing the quarter round.