Table of Contents
How do you convert Aqua Rite to metric?
To change the unit from Metric Mode to US Standard , start by pressing the ‘Diagnostics’ button one time. Once showing the temperature in Celsius, move the switch up to ‘Super Chlorinate’ then back to ‘Auto’. After 30 seconds the unit should settle back to the default reading.
What should my salt chlorinator be set at?
To make your salt water chlorinator last, you’ll need to perform regular maintenance on it just as you do every other part of your pool. Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal.
What should the setting be on a Hayward chlorinator?
The safe operating range of pH is between 7.2 and 7.8 PPM.
How long should you super chlorinate a salt water pool?
To decontaminate, you need to super-chlorinate or super shock the pool or spa water with granular chlorine (or substitute granular bromine or lithium for chlorine). Our goal is to maintain 20ppm or more of chlorine for 72 hours.
How do I calibrate my Hayward Goldline?
This step can get tricky and may need to be repeated. While on the calibration screen and with the pool pump still running, push the “Auto” switch down to the “Off” position for two seconds. Now push the switch back up to the “Auto” position again. Wait approximately 10 seconds (you will hear the relay kick on).
How do I reset my Aqua Rite salt cell?
Reset AquaRite Salt Chlorination Inspect Cell Light If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
How much salt does my pool need calculator?
Quick Reference: Salt Need Estimator
| Current Salt Level | Salt Needed | |
|---|---|---|
| 8,000 Gallon Pool | 12,000 Gallon Pool | |
| 1,000 | 147 lbs. | 220 lbs. |
| 2,000 | 80 lbs. | 120 lbs. |
| 3,000 | 13 lbs. | 20 lbs. |
What should my salt generator read?
The normal range for most pools is around 2500 to 3500 ppm, with the ideal value being 3200 ppm. This depends on your saltwater chlorine generator (SWG) model though. If the salt reading goes below the normal range for your model, usually a “check salt” or “low salt” LED light will start flashing.
What setting should I have my chlorinator on?
Your salt levels will vary depending on the type of chlorinator you have. If you’re using the Water TechniX Salt water chlorinator then you should try to aim for a salt level of around 3,000 to 4,000 ppm.
Can you swim while Super chlorinator is on?
The high levels of chlorine used when Superchlorinating pools can make them dangerous to swim in, so always make the pool or spa off limits while you Superchlorinate it. Superchlorination will only last about a day after adding the chemicals. To be sure, you should always test the pool after Superchlorination.
Can you swim after Super chlorinate?
Avoid swimming in the pool after Super Chlorination. High levels of chlorine are toxic and the water should be tested prior to re-entering the pool following a shock treatment. No one should enter the pool until the chlorine level has returned to or lower then 3ppm (Parts Per Million).
How do you reset aqua rite electronic chlorine generator?
To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.
How long do salt cells last?
about five years
This is all possible thanks to your pool’s salt chlorine generator cell. With proper care, a cell will last about five years. Eventually, though, it will need to be replaced.