How do I adjust my Kinetico water softener?
Push the water softener valve screw in firmly with a screwdriver, then turn the screw clockwise slowly–never counterclockwise–until you see the tab reach the black indicator dot in the Brine position. Depending on your model, you will see Brine/Rinse written on your water softener head.
How do I set the regeneration time on my Kinetico water softener?
To start a regeneration cycle, move the disk post just past the two lines to either one of the two Brine Rinse positions. The softener will then run a cycle for one of the tanks. This will usually take around 30-60 minutes depending on the size of your softener.
How often should my Kinetico water softener regenerate?
every two to three days
It is generally agreed upon that regular regenerations are the best, because they keep the resin bed active. This should be every two to three days, although highly efficient softeners may generate every day or even multiple times a day.
How do I adjust the hardness in my water softener?
Press the UP or DOWN buttons to set your water hardness number. NOTE: If your water supply contains iron, compensate for it by adding to the water hardness number. For example, assume your water is 20 gpg hard and contains 2 ppm iron. Add 5 to the hardness number for each 1 ppm or iron.
How do you start a Kinetico water softener?
Using a #2 Phillips screwdriver, push down firmly on the softener valve screw and slowly turn clockwise to start the regeneration. At this point you should hear water begin to run through the system.
Why is my water softener not regenerating automatically?
It might not regenerate due to a malfunctioning timer or the brine tank is having a problem so the resin cannot fully recharge. Another possible explanation is a dirty or depleted resin bed.
What happens if I use water while my water softener is regenerating?
It is not recommended to use water during a water softener regeneration, as hard water will fill the water heater, which could lead to buildup in the equipment.
What should my water hardness be set at?
The rule of thumb is that a good hardness level should not be higher than 120 to 170 mg/L, i.e., seven to ten grains per gallon of water. An accurate water analysis report should show you the hardness level. You can get the water tested in a lab, or do it yourself at home with a water hardness test kit.
How often should a Kinetico water softener regenerate?
So your system regenerates whenever necessary, at any time of day. And Kinetico’s twin tank design allows one tank to provide treated water while the other regenerates, so you’ll never be without soft water. How will I know when it is time to add salt?
How long is a water softener cycle?
Water softener regeneration cycle time is about two hours. It is not recommended to use water during a water softener regeneration, as hard water will fill the water heater, which could lead to buildup in the equipment.
How can I tell if my water softener is not working?
You may have started to notice water spots on your shower doors, a change in your home’s water pressure, or your water just doesn’t feel soft. These can all be signs that your water softener is not working properly.
Is this an original Kinetico document?
1Kinetico is a registered trademark of the Kinetico Corporation. This is not an original Kinetico document. The content has been taken from Kinetico’s “Owner’s Manual” for residential water softeners. This was produced to aid Air & Water Quality’scustomers that may have lost there original manual.
Do I need to do anything special to operate my Kinetico?
You really don’t need to do anything special to operate your Kinetico water system —it runs itself, not you. Your Kinetico water system has a built-in water meter which means it operates “on demand” based on your actual water usage.
Why choose Kinetico Water Systems?
Owner’s Manual Congratulations for choosing Kinetico to improve the quality of your water. You will immediately begin to notice the numerous benefits of having quality water throughout your home and the benefits of having a Kinetico Quality Water System.
Where can I find more information about Kinetico products?
For more information, contact your authorized Kinetico dealer or visit our web site at www.kinetico.com. Kinetico fabrique une gamme complète de produits de traitement de l’eau pour répondre à la plupart des problèmes d’eau.