How to add fibaro double switch?

How to add fibaro double switch?

Installation of the device:

1. Switch off the mains voltage (disable the fuse)
2. Open the wall switch box.
3. Connect with one of the diagrams below.
4. Verify correctness of connection.
5. Arrange the device and its antenna in a wall switch box.
6. Close the wall switch box.
7. Turn on the mains voltage.
8. Add the device to the Z-Wave network.

How do I reset my Fibaro switch?

Resetting the device:

1. Disconnect the power supply.
2. Remove the device from the wall switch box.
3. Connect the power supply.
4. Locate the B-button on the housing.
5. Press and hold the B-button for 3 seconds.
6. After few seconds the device will be reset.

What is a dual relay switch?

DoubleSwitch is a relay switch that you toggle via hobby radio control gear. You can use DoubleSwitch to quickly and easily control lighting systems with two different voltages, motors, pumps, smoke generators, sound units and more! Will also control glow plugs and BattleBot weaponry.

How do you wire a Fibaro?

How does a Fibaro switch work?

The FIBARO Single/Double Switch enables to turn on/off any electrical device remotely. Turn your dishwasher on or automatically cut the power off in case of a malfunction at any time. You can control all the household appliances you own by cutting the power off or turning it on in the socket.

How do I reset my Fibaro wall plug?

Wall Plug – “Reset”

1. Insert the device into a socket.
2. Press and hold the B-button.
3. Wait for the visual indicator to glow yellow.
4. Release the B-button.
5. Press the B-button again, briefly.
6. Successful reset will be confirmed with the visual indicator changing colour to red.
7. Visual indicator and Wall Plug’s relay will turn off.

How do I reset my Fibaro dimmer?

Resetting the Dimmer 2:

1. Disconnect the power supply.
2. Remove the Dimmer 2 from the wall switch box.
3. Connect the power supply.
4. Locate the B-button on the housing.
5. Press and hold the B-button to enter the menu mode.
6. Wait for the visual LED indicator to turn yellow.
7. Quickly release and click the B-button again.

Can you use 2 relays in parallel?

In general, if two relays are connected in parallel, the continuous current-handling ability of the combination will be almost equal to the sum of the individual relays’ abilities, but the switching ability of the combination may be that of the worse relay, and in many cases won’t be much better than that of the better …

Can you use 2 relays in series?

We cannot recommend the use of relays in series connection on the input side because it may cause (transitionally) an undervoltage or an overvoltage due to differences in coil resistance. When you use multiple relays, connect them in parallel basically to make sure that the rated voltage is applied to the coils.

Is Fibaro any good?

Fibaro’s app is decent, though not great. While it shows you your whole home, and exposes a bit of additional information like the last time motion was detected versus Apple’s Home app, it is limited in function, and has a poor layout. To create some great rules, our preferred app is Eve.

Who is Fibaro?

FIBARO is a global brand based on the Internet of Things technology. It provides solutions for building and home automation. FIBARO’s headquarters and factory are located in Wysogotowo, 3 miles away from Poznan. The company employs app.

How do you wire a Fibaro wall plug?

1. Insert the device into a socket within the direct range of your Z-Wave controller.
2. From your Vera’s Dashboard, go to Devices > Add devices.
3. Choose a Generic Z-Wave device from the list.
4. Follow the instructions on screen.
5. Quickly, triple click the B-button.
6. Wait for the adding process to end.

How do I reset my Fibaro dimmer 2?

Can you put relays in parallel?

You can parallel switches (relays) only if you are sure that they will switch together at the some time and with the same dI/dt. It is possible, but difficult. Do not compare with paralleling thyristors or triacs to make a bigger one.

What is remotely controlled double relay switch of Fibaro?

Remotely Controlled Double Relay Switch of FIBARO System is designed to operate in a wall switch box or in locations where the control of two electric devices is needed. 2. What voltage Relay Switch module should be powered by?

How do I add a device to my Fibaro hub?

Identify switch no. 1 (turns the light on) or the B-button (located on the device’s housing) Click the Plus (+) icon on the Home Screen. Select FIBARO and click on the device. Choose a hub you want to add your device to and click Next. Choose a room where the device will be placed and click Next.

What is the difference between different Fibaro modules?

Fibaro produced (till now) modules from v1.0 to v2.1. Modules differs by internal software and version of Z-Wave libraries. (Z-Wave requires that module support most current libs. at the time of release). In version 1.6 Fibaro introduced varistor protection.

What is the overcurrent protection of a Fibaro switch?

The device must be protected with an overcurrent protection (fuse) with a value not higher than 10A. FIBARO Double Relay Switch is designed to be installed in standard wall switch boxes or anywhere else where it is necessary to control two independent devices drawing up to 1500W each.