How do I reset my APC password?
Press the Reset button a second time immediately while the LED is flashing to reset the user name and password to their defaults temporarily. Then press ENTER as many times as necessary to redisplay the User Name prompt, then use the default, apc, for the user name and password.
How do I factory reset my APC PDU?
Resetting APC AP7920 PDU
- Press and hold the reset button for about 10 seconds.
- The status light should blink rapidly.
- Release the reset button then press it again for about a second.
- The light should go orange.
- After about 20 seconds the reset will complete and the device will have booted.
What is APC bypass mode?
Re: Bypass mode in APC Smart-UPS 750RM with the automatic transfer switch, it is sort of like a bypass where basically if one AC input (the UPS) fails, it will switch to an alternative (secondary) AC source. ideally each source should be its own circuit for full redundancy.
What is APC UPS bypass mode?
What is UPS Bypass Mode? UPS Bypass mode is when you switch the circuit from going through the UPS to going around or bypassing it. A manual bypass switch is used to remove the UPS system from the circuit for servicing or maintenance or if it is no longer working correctly.
How do I reset my mini up?
Turn it back ON. Other option: Reset to factory settings: press 15 seconds from the OFF state (unplugged). Then plug UPS and restart UPS. It is recommended to fully charge the battery after initial setup and if possible, to perform two or three cycles of charge/discharge.
What is the default password for apc PDU?
what is default password for apc pdu? The default username and password for apc pdu is “apc”. It is a common username and password and can be used for setup and installation of APC Management Card setup, BOOTP and DHCP configuration, Local access to the control console among others.
What is a apc password?
The default username for your APC UPS is apc. The default password is apc.
What is electrical bypass switch?
The external Maintenance Bypass switch allows you to manually transfer your connected equipment to utility power permitting scheduled maintenance, or complete UPS replacement, without power disruption. The switch has two modes of operation, UPS mode and Bypass (maintenance bypass mode).
What does UPS bypass unavailable mean?
This message occurs when the UPS is online, and indicates that static Bypass operation may not be available while the alarm is active. If the Bypass frequency is out of range, the UPS should not allow you to command the UPS to bypass.
How does a UPS bypass switch work?
What Does A Bypass Switch In A UPS System Do? A static bypass switch automatically and instantaneously transfers the load to the mains electricity supply when there’s an internal fault or failure with the UPS system.
How do I factory reset my apc PDU?
What is UPS bypass mode?
o The Bypass button indicates that the UPS is in Bypass mode. This means that something has gone wrong with the UPS and power is bypassing the battery portion of the UPS, but is still traveling through the UPS unit itself. In this mode there is no protection from a power failure.
How do I change the PowerChute service password?
Start the PowerChute service and log in with your new username and password. For security, the password line will be deleted from the pcnsconfig.ini file when the PowerChute service is restarted. The new password must meet the password requirements laid out in the PowerChute Network Shutdown user manual or this process may fail.
How to add a password to the power chute?
For the client powerchute application there is a pcnsconfig file under C:Program FilesAPCPowerChutegroup1 that you add ‘password = password’ under the first section. Stop and enter that in and then start the service back up.
What are the authentication requirements for PowerChute Network shutdown (PCNs)?
The administrator authentication phrase used by PowerChute Network Shutdown (PCNS) should be the same as that used in the NMC. The default used by the NMC is: admin user phrase. The authentication phrase must be at least 15, but no more than 32 characters. You must use ASCII characters A-Z, a-z, 0-9.
How do I stop PowerChute from running?
Stop the PowerChute service. 2. Go to the group1 directory where PowerChute is installed. 3. Make a backup of the pcnsconfig.ini file – copy it to another directory and rename it to pcnsconfig-backup.ini. 4. Open pcnsconfig.ini in a text editor. 5.