Useful tips

Do basements need special drywall?

September 6, 2022

Do basements need special drywall?

Basement Board: This type of drywall, usually used in basements, has a standard core and mold-resistant face and back paper. It’s not as effective as standard mold and moisture-resistant drywall, but it’s less expensive.

Is it expensive to drywall a basement?

Cost to Drywall a Basement Installing drywall costs an average of $1,850 or about $2 per square foot. Finishing basement walls in a 400 square foot space may run you $800, while 1,500 square feet is closer to $3,000.

Should I drywall my basement walls?

Typical drywall is made of two paperboards that sandwich gypsum, a powdery mineral material. In a basement, there’s always the risk of water intrusion or plumbing leaks, leaving any basement walls finished with drywall at risk.

How do I redo my basement walls?

  1. Seal the Wall. Use a paint roller to apply the masonry waterproofing product you choose.
  2. Install Blocking Between Joists.
  3. Snap Lines on the Floor.
  4. Assemble the Walls on the Ground.
  5. Tip Up the Walls.
  6. Plumb the Wall and Secure the Top Plate.
  7. Build Out Around Windows.

How do you cover up old basement walls?

Drywall. The most common way to cover concrete walls in a basement is drywall, a.k.a. sheetrock. Drywall comes in panels panels made from calcium sulfate dihydrate or “gypsum.” Panels come in different thicknesses and sizes, the most common being 4′ x 8′ x 1/2″ thick.

How do people afford to finish a basement?

5 ways to finance a basement remodel

  1. Home equity line of credit (HELOC)
  2. Home equity loan.
  3. FHA 203k loan.
  4. Personal loan.
  5. Contractor financing.

What is the cheapest way to refinish a basement?

You can save on the cost to finish a basement by doing things not bound by codes: installing trim or doors, painting walls and woodwork, and installing flooring, says Buckeye Basements’ Jon Smith. Beyond that, count on using some pros.

How can I save money to remodel my basement?

7 ways to save on your basement remodel

  1. Opt for an inexpensive, prefabricated egress window and well.
  2. Test exterior walls for moisture before finishing.
  3. Cut out some studs.
  4. Install drop ceilings.
  5. Skip the carpet and install luxury vinyl tile instead.
  6. Add a bathroom (or at least a half bath) near existing plumbing.

How do you install drywall in a basement?

Cut a piece of drywall 1/4-inch short to fit between the corner and the last installed panel.

  • Screw the drywall in place.
  • Where the panels meet,cut a V-groove into the short non-tapered ends with a utility knife,as this will make hiding the joint easier when you’re taping.

    • Which drywall is best for basements?

    Masonry Wall. The most affordable basement construction options,a masonry wall basement consists of a wall of concrete cinder blocks stacked upon each other.

  • Poured Concrete. This is the preferred method of basement and foundation construction.
  • Precast Panel Basements. This is the least common of the three basement options.
  • Exposed Stone or Brick.

    • How to finish a basement without drywall?

    – Cleaning the space – Removing and treating for mold and mildew – Waterproofing – Installing or adding a back-up sump pump – Installing a dehumidifier

    How to install wood paneling on basement walls?

    Scrub the wall with a wire brush and a mixture of 1/2 cup bleach per gallon of water to remove dirt and mold.

  • Stand the first 2-by-4,wide side flat,against the wall. Nail it in place with the powder-actuated nail gun.
  • Measure 16 inches from the center of the first 2-by-4 and nail the next one against the wall.

    • You May Also Like

    Your copyright text here !