What is FlexConnect mode?
It enables customers to configure and control access points (AP) in a branch or remote office from the corporate office through a wide area network (WAN) link without deploying a controller in each office.
What is FlexConnect AP mode?
FlexConnect is an AP mode for situations like the one above. The AP can locally switch traffic between a VLAN and SSID when the CAPWAP tunnel to the WLC is down.
What is CPU ACL?
By using a CPU ACL (access control list) you can lock down which IP networks or IP addresses are allowed to communicate to the WLC CPU which is where you would have to go to make changes to the configuration, get SNMP data, and much more.
What is FlexConnect local authentication?
local authentication, local switching—In this state, the FlexConnect access point handles client authentication and switches client data packets locally. This state is valid in standalone mode and connected mode.
How do I check my ACL on Cisco WLC?
You can use “show rules”command to verify exising rules on a WLC. You can override these by CPU ACL if you use the same protocol/port numbers. This is shown partial list of the output of that command. In CLI, you can use “show acl cpu” to view ACL applied to CPU.
What is Cpuacl?
Whenever you want to control which devices can talk to the main CPU, a CPU ACL is used. It is important to mention several characteristics for these: CPU ACLs only filter traffic towards the CPU, and not any traffic exiting or generated by the CPU.
What is the difference between CAPWAP and Lwapp?
CAPWAP is an abbreviation for Control and Provisioning of Wireless Access Points protocol (CAPWAP), which is based on LWAPP, which is a standard, interoperable protocol that enables a controller to manage a collection of wireless access points.
What does a FlexConnect local switching WLAN or SSID do?
i) Local Switched ( Flex Connect Mode) –> Locally-switched WLAN’s (the SSID you are connected to) will map their wireless user traffic to a VLAN via 802.1Q trunking to a local switch adjacent to the access point. –> Traffic is forwarded using branch router in the network in this mode.
What is the benefit of using Cisco wireless LAN controller?
A wireless LAN IDS reduces the threat of hackers or malicious users gaining access to critical network resources. Cisco lightweight access points and wireless LAN controllers simultaneously act as data-serving devices and IDS sensors.
What is the expansion for CAPWAP?
Control and Provisioning of Wireless Access Points
CAPWAP (Control and Provisioning of Wireless Access Points) CAPWAP (Control and Provisioning of Wireless Access Points) is a protocol that enables an access controller (AC) to manage a collection of wireless termination points.
Is FlexConnect Cisco proprietary?
Cisco FlexConnect (or H-REAP, Hybrid Remote Edge Access Point) is Cisco proprietary solution for Wireless Controller (WLC)-dependant APs.
What is Capwap in WLC?
CAPWAP (Control and Provisioning of Wireless Access Points) is a protocol that enables an access controller (AC) to manage a collection of wireless termination points.
What are the pros and cons of a wireless communication system?
Here are the pros and cons of a wireless network installation.
- Increased efficiency.
- Cost savings.
- Wireless networking offers more flexibility.
- A safer workplace.
- A better looking workplace.
- Security.
- Installation and usage problems.
- Transmission speeds.
How do I configure ACL mapping for flexconnect APS?
All the APs in the FlexConnect group receive the ACL that is configured. This can be configured as you navigate to Wireless-Flexconnect Groups > Select the group you want configure > ACL mapping > Policies, and add the name of the Policy ACL as shown in the image: 2. AP Specific
What is the difference between AP ACL and flexconnect ACL?
If a VLAN is configured on both the FlexConnect group and also on the AP (as a AP specific configuration), then the AP ACL configuration takes precedence. If the AP specific ACL is configured to none, then no ACL is applied.
How are flexconnect ACLS applied to vlan interfaces?
The FlexConnect ACLs can be applied to VLAN interfaces on access points in both the Ingress and Egress mode. Existing interfaces on an access point can be mapped to ACLs. The interfaces can be created by configuring a WLAN-VLAN mapping on a FlexConnect access point.
How to configure an IP address based rule for flexconnect ACL?
Configure an IP address based rule for a given FlexConnect ACL as follows: Choose IP Rule to create an IP address based rule. The Access Control Lists > Rules > New page is displayed. The controller supports up to 64 rules for each IP address-based ACL.