How do I access my Buffalo NAS?
To test access, go to BuffaloNAS.com and enter the name you assigned. You should be taken to the WebAccess interface for your LinkStation. If this does not work, it is likely either port forwarding settings in the router are incorrect, or you are attempting to use an external port that is blocked by the ISP.
How do I access Buffalo TeraStation from the Internet?
6Configure each setting as below.
- Select. Enable. for. Web Access Service. .
- Select. Enable. for. Use BuffaloNAS.com. .
- Enter a desired name into. BuffaloNAS.com Name. . Take note of this BuffaloNAS.com name. This will be used to open a shared folder from a remote location.
- Select. Enable. for. Auto-Configure Firewall (UPnP) .
- Click.
What is the default password for Buffalo NAS?
If NAS Navigator is not installed, download and install the application by clicking on the provided URLs here: Windows or Mac. Log in to Settings. The default username and password are “admin” and “password”.
What is BuffaloNAS com key?
BuffaloNAS.com Key This is the password (“key”) that protects your LinkStation’s or TeraStation’s BuffaloNAS.com name. Try to select a password that is not easily guessed by others.
How do I add files to Buffalo NAS?
Uploading One File
- Click. File. > Upload. from the menu bar while logged in.
- Click. Browse. and select the file to upload.
- Click. Upload. .
- Click.
How do I factory reset my Buffalo NAS?
Initializing from Settings
- In Settings, navigate to [System] – [Restore/Erase].
- Click [Restore LinkStation].
- The “Confirm Operation” screen will open. Enter the displayed number within 60 seconds, then click [Apply].
How do I register my BuffaloNAS com name?
If you close the welcome screen, you can register directly from the NAS List with the procedure below. Tap . Tap [Name], enter a name for this connection, and then tap . Tap [Registration Type], then select [BuffaloNAS.com Name].
How do I reset my Buffalo TeraStation admin password?
TeraStation TGL / HTGL / RHTGL / ITGL / RITGL / DHTGL / TS-X series
- Open the front panel and look under the left corner of the LCD screen for the red Init button.
- Press and hold the red button for 10 seconds. The device will start beeping. The password and IP address has been changed to default.
How do I map a Buffalo NAS drive?
Right-click on the NAS.
- Select “Browse Shares” from the pop-up menu.
- Right-click on the shared folder you want to map to a drive letter.
- Select “Map network drive…” from the pop-up menu.
- Click on the drop-down menu to change the drive letter if desired.
- Select the desired drive letter.
- Click Finish to map the drive.
How do I format a Buffalo NAS drive?
To format hard drives, select the hard drive(s) that you want to format and click on Format Disk. if you prefer a more thorough method, connect the LSL via USB to a computer and nuke the drive with DBAN or active@Killdisk. then connect it to the network again and format the drive as described above.
What is Buffalo Technology’s web access service?
Buffalo Technology’s Web Access feature is offered as a service for Buffalo Technology customers. Buffalo Technology provides not guarantee or warranty of its operation and is not responsible for the content on users’ NAS devices. NAS owners are responsible for following their respective laws and ISP rules regarding content distribution.
How do I connect my Buffalo to my computer?
Go to Buffalo’s website. Go to www.buffalotech.com and download WebAccess for Windows. Install WebAccess. Locate the setup file on your desktop and double-click on it to run it. Do the initial setup for WebAccess. Before you’re able to access your files and folders in your NAS, you have to properly link the device to your computer.
What is WebAccess and how do I use it?
WebAccess is a cloud service provided by Buffalo that allows you to access your NAS remotely over the Internet. You can share content with everyone or with specified users only. You can set up WebAccess through your NAS, or enable the service on your AirStation. If you have a BuffaloNAS.com account, you can use its login to use WebAccess.
How do I set up the Buffalo NAS DNS service?
Select the DNS Service Hostname used to access the service. If you have a BuffaloNAS.com account, select [Use BuffaloNAS.com Registration] and enter your BuffaloNAS.com username and password. You can also use an existing hostname, such as your dynamic DNS hostname.