Why does my waeco fridge flash orange?
The “power” led was flashing orange after a rough road. A green steady means the compressor is running. The fridge temperature is ok if the compressor is orange steady.
What voltage does a waeco fridge cut out?
According to the manual, at medium setting the fridge should cut out at 11.4 volts and restart at 12.2 volts.
How many Litres is a CF 50 waeco?
Short description:
| Capacity: | 41 litres (holds 40 cans in the basket) |
|---|---|
| System: | Fully hermetic Waeco ACV20DC compressor with integrated electronic controls, reverse polarity protection, low voltage protection, dynamically ventilated wire tube condenser, aluminium rollbond evaporator |
What resistance is waeco thermistor?
Waeco CF fridges use a 10k ohm thermistor. Resistance decreases as temperature rises. So if the internals of the thermistor have shorted out, there will be zero (or nearly zero) resistance. And if the resistance is zero, then the fridge controller will think the fridge temperature is at or above 80°C.
Can waeco fridges be repaired?
Whatever the problem, Selective Fridges refrigerator repair mechanics will be able to repair and service your Waeco fridge promptly and effectively in your home to extend the life and efficiency of your portable fridge or freezer.
Do waeco fridges need Regassing?
Re: Do Waecos need regassing Being a compressor fridge it uses gas. However it would only ever need re-gassing if it has leaked via damage or broken seal etc which doesn’t happen very often. If it is not working properly would suggest some cause other than low in gas.
What temperature should I run my waeco fridge?
In fact, the ideal temperature for your fridge compartment is approximately 2-3°C as this offers the perfect balance between having your food spoiled and having your food frozen. The freezer compartment should be at a temperature of approximately -10°C to -20°C depending on what you want to keep frozen.
How long does a battery last on a camping fridge?
In general, a 12V-50Ah battery can run a 2 cubic feet 12V fridge for 35 to 50 hours before it’s completely depleted. A 10 cubic feet RV refrigerator can run on the same battery for only 10 to 15 hours.
What is the difference between a waeco CF and CFX?
These two models share similar qualities. The main difference is that the CFX Series can really get a deep freeze down to -8ºF. The CFX is also a smart refrigerator.
How long does a waeco last?
If you use an average of 3a, 1 x 70ah battery, at 100% capacity, it has a theoretical probability of running the fridge for 23 hours. If it was left in freeze mode and drew 3.6a or more for the full period, you will only have 20 hours on a 100% 70a battery.
Can Waeco fridges be repaired?
How do I reset my waeco fridge?
Reset to factory settings by using reset function on fridge. Press “SET” 5 times (single compartment models), or 6 times (two compartment models), then press/hold the “+” button for at least 5 seconds.
Is there a thermistor repair kit for a WAECO fridge?
Thermistor Repair Kit for Waeco CF18, CF25, CF35, CF40, CF50, CF60, all VERA, all VERB, CDF35 and CDF45. These fridge units require only a single thermistor cable replacement as provided (OEM)
Are there any problems with WAECO fridges?
The CF range of Waeco fridges have a known fault. The thermistor often fails after several years. If you have a temperature problem with your Waeco fridge, then there’s a good chance the thermistor has died. Waeco install the thermistor at the bottom of the fridge on the underside.
Why does my cf40 compressor keep freezing up?
WAECO CF40 Thermist… Ok so during my last trip, my trusty WAECO CF40 started freezing everything and the compressor just kept running. This is due to the fridge’s temp sensor or technical name is a thermistor going short circuit.
Where is the thermistor located on a cf-50 freezer?
Some are underneath (our CF-50 CoolFreeze) while others are in various places around the side walls, including behind the compressor/evaporator unit. The location of the thermistor, where it disappears into the foam insulation and where it terminates on the printed circuit board varies between models.