Table of Contents
How do you get output waveform in PSpice?
Add the waveform for output voltage on this axis by clicking on the Add Trace icon, and selecting Vout from the trace list. PSpice has the ability to retrieve the previous plot settings, even when you make any changes to the schematic. Enable last plot from the Probe Window settings in the simulation setup.
How do I get VCC in PSpice?
Select Place > Power and scroll down to the VCC_CIRCLE symbol and in the Name: box, change the name to VCC and click on OK.
How can I add GND in PSpice?
Every circuit that is simulated on PSPICE must have a ground node indicated. This is done by entering the ground symbol. To place the ground, select Place→ Ground (or click on the ground symbol on the toolbar). Select the “Source” library and the ground part labeled “0”.
What is .probe in PSpice?
The PROBE statement included in the PSPICE Netlist generates a file, PROBE. DAT, for viewing the analysis on the computer monitor. If the PROBE program is executed, an output can be obtained as shown in the figure.
What is voff in PSpice?
Voff is the DC offset value. It should be set to zero if you need a pure sinusoid. Vamplitude is the undamped amplitude of the sinusoid; i.e., the peak value measured from zero if there were no DC offset value. FREQ is the frequency in Hz of the sinusoid.
What is Vpulse in PSpice?
Pulse Waveform A voltage pulse or pulse train can be applied as an independent source in PSPICE using the VPULSE element. VPULSE has seven parameters that describe its shape as shown in figure 1.
How do you use current markers in PSpice?
Voltage and current markers are used to probe the voltage or current. After simulation, PSPICE automatically plot the results. Select Markers/Mark Voltage/Level [Ctrl+M] or click voltage marker icon to place the voltage marker. Select Markers/Mark Current into Pin or click current marker to place the current marker.
What is Vampl in PSpice?
For VSIN power supply, VAMPL is the parameter that represents “peak” amplitude of voltage. This has been mentioned in PSpice reference guide for ISIN (Current counetrpart of VSIN).
What is voff in pspice?
How do I start Ngspice?
- Introduction.
- Download and Install ngspice (MS Windows)
- Download and Install ngspice (Linux)
- Circuit with Passive Elements, Operating Point.
- Circuit with Passive Elements, Transient Simulation.
- Circuit with Passive Elements, small signal AC Simulation.
- Download and Install a Simple GUI (MS Windows)
- Bipolar Amplifier.
What is G in PSPICE?
G Device – Value Form. H. Current-Controlled Voltage Source. HPOLY. Current-Controlled Voltage Source.
How do you add power probes in PSpice?
In the schematic, select the Voltage Probe button on the toolbar or select PSpice > Markers > Voltage Level from the menu.
- Click to place a probe at the Input and Output.
- Select PSpice > Run from the menu.
- View the PSpice A/D Window.
- Back in the schematic, select the probes and press Delete.
Who invented PSpice?
SPICE
| Original author(s) | Thomas Quarles |
|---|---|
| Stable release | 3f.5 / July 1993 |
| Written in | C |
| Type | Electronic circuit simulation |
| License | BSD license (modified 2 clauses) |
What is difference between Matlab and PSpice?
PSpice is a program to simulate analog and digital logic circuits, where Matlab is a fully functional programming language designed to plot mathematical functions, implement various algorithms and solve complex mathematical problems.
Is Ngspice free?
al. Ngspice is based on three open-source free-software packages: Spice3f5, Xspice and Cider1b1: SPICE is the origin of all electronic circuit simulators, its successors are widely used in the electronics community.