Table of Contents
What is a broom finish on concrete?
Broom Finish concrete is concrete finished by dragging a horsehair broom, or something similar, over its wet surface. Brushing the concrete makes for a textured surface with small, but noticeable grooves. Broom Finish concrete has been the preferred utilitarian texture for exterior concrete for decades.
When should you broom finish concrete?
When it comes to brooming, timing is critical—brush too early and the surface will be weak, brush too late and there won’t be enough texture. It must be done while the slab is still soft, but after the bleed water has dissipated. Depending on the weather, this can take anywhere from 20 minutes to 4 hours.
How much is broom finish concrete?
Because the work is labor and material intensive, expect to pay from $2.50 to $5 per square foot for a four-inch thick, broom sweep-finish concrete patio. For stamping, plan to spend around $6 per square foot in most regions.
What is broom finished driveway?
Broom finishes, the most common surface textures for exterior flatwork, are created by pulling a broom over freshly placed concrete. Brooming creates a textured or slip-resistant surface with grooves typically installed crosswise (perpendicular) to the direction of travel.
What are the advantages of broom?
The Advantages of a Broom & Dustpan over Hoovers
- Cleaning smaller areas.
- You’re trying not to wake up the whole house.
- You want to do your part for the environment.
- Those hard to reach places.
- Larger items that can damage your hoover.
Is brushed concrete slippery?
Broomed/brushed concrete requires little maintenance and isn’t slippery.
What are the advantages and disadvantages of broom?
Advantages and Disadvantages Traditional wooden brooms are heavier but they are also stronger and can withstand more use. The weight of a wooden broom gives it stability and momentum for hard sweeping chores. Brooms with hollow aluminum handles are lighter but easier to break.
Do you seal broom finish concrete?
Sealing a Broom Finish However, if not maintained with sealer, over many years of rain exposure it will lose its broom finish and look more like exposed aggregate (due to the slightly acidic nature of rainfall). Because of this, we recommend that you seal broom-finished concrete so it maintains its intended look.
Is brushed concrete rough?
A brushed concrete finish gives you a rough texture on the surface of a concrete floor. You apply a brushed concrete finish when you want the floor to have slip resistance, such as on an outdoor walkway, and you do it by dragging a stiff-bristled broom or brush across a fresh concrete surface.
What type of concrete should you use for driveway?
The best concrete mix for driveways is at least 3500 psi compressive strength and 5-6 inches thick over compacted gravel and earth with a water to cement ratio of . 50 and aggregate less than an inch.
Is trowel finish concrete slippery?
Trowel-finished concrete floors are slip-resistant The trowel-finished concrete floor’s particular rough texture and high-adhesion make it a slip-resistant surface. For this reason the trowel concrete floor is ideal for outdoor applications such as pooldecks and walkways.
What can I use instead of a broom?
broom
- mop.
- besom.
- swab.
- sweeper.
- whisk.
- carpet sweeper.
- feather duster.
- floor brush.
Should I seal my new concrete driveway?
A driveway sealer should be applied after the freshly poured concrete has cured. Most contractors find success waiting 7 to 14 days, but the official time for curing is 28 days. If you are having a patio poured at the same time, it should also be sealed.
What thickness should a concrete driveway be?
four inches
As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
Does a concrete driveway need rebar?
The presence of rebar in a concrete project gives the final project considerably more strength than concrete alone. This strength is crucial for things like buildings, roads and driveways. Rebar is not necessary for every concrete project.