What is LR3 zoning in Seattle?
What is this? To illustrate this, let’s look at the Lowrise 3 (LR3) zone, a relatively common multi-family residential zone in Seattle. LR3 zones are generally proposed to get a height limit boost from 40 feet to 50 feet and a floor area ratio (FAR) increase from 2.0 to 2.2 as MHA LR3.
What is zoning Seattle?
What Is It? Our Zoning Code governs the use and development of land in Seattle. Zoning districts specify a category of uses (e.g., neighborhood residential, multifamily residential, commercial, industrial, etc.) and are applied by ordinance.
What is RSL M in Seattle zoning?
The RSL zone would encourage more “missing middle” housing that is in between the density of Seattle’s and single-family and multifamily zones. The RSL zone would result in moderately- sized ownership and rental housing options suitable for families or multi-person households.
What is the minimum lot size in Seattle?
Zone Minimum lot area SF5000 5000 square feet SF7200 7200 ” SF9600 9600 ” Various exceptions allow for smaller lots, most commonly when other existing lots on the street are also undersized. As shown for most lots.
How does MHA work in Seattle?
policy to ensure growth brings affordability Mandatory Housing Affordability (MHA) ensures that new commercial and multi- family residential development contributes to affordable housing. MHA will provide at least 6,000 new rent-restricted homes for low-income people.
What is single-family zoning Seattle?
Seattle’s zoning already permits three housing units on single-family lots: a primary dwelling, an attached unit (ADU) and a detached unit (DADU). This allows denser housing that still preserves traditional neighborhoods.
How much of Seattle is single-family zoned?
The level of support was only a little lower for the same change in suburban neighborhoods, at 51%. Currently, the majority of Seattle’s residential areas are zoned for single-family homes and “accessory units” like backyard cottages, but do not allow for larger apartment buildings and condos.
What does RSL stand for in real estate?
‘the RSL means a registered social landlord as defined in Part 1 of the Housing Act 1996, who is registered with the Housing Corporation pursuant to Section 3 of that Act and has not been removed from the register pursuant to Section 4 of that Act, and who is approved by the Council (such approval not to be …
What does RAL stand for in real estate?
Residential Assisted Living
The senior living sector has expanded to include a new housing opportunity for real estate investors with Residential Assisted Living (RAL).
How close can you build to the property line Seattle?
Seattle is fairly flexible about where you can put a small shed structure, allowing them in the front, side, or rear yard. You are, however, subject to the same setbacks as garages: 20 feet from the front property line, 5 feet of the side property line.
How high can you build a house in Seattle?
The base height of homes (principal structures) is 30 feet above average grade (23.44. 012). On lots 30 feet or less in width, the base height is limited to 25 feet (detailed measurement techniques are found in Chapter 23.86 of the Land Use Code and in Director’s Rule 9-2011).
What is MHA in Seattle?
Mandatory Housing Affordability (MHA) ensures that new commercial and multi- family residential development contributes to affordable housing. MHA will provide at least 6,000 new rent-restricted homes for low-income people.
What is an MHA area?
Mandatory Housing Affordability (MHA) is a program that ensures new commercial and multifamily residential development contribute to affordable housing. MHA will provide at least 6,000 new rent-restricted homes for low-income people.
What is the LR2 zoning in San Diego?
The LR2 zone provides for a vari- ety of multifamily housing types in existing multifamily neighborhoods and along arterial streets. LR2 is most appropriate for areas within Growth Areas***.
What is an LR2 zone in NYC?
The LR2 zone provides for a vari- ety of multifamily housing types in existing multifamily neighborhoods and along arterial streets. LR2 is most appropriate for areas within Growth Areas***. A mix of small scale to multifamily housing such as townhouses, rowhouses and apartments are encouraged.
Is there a lowrise zoning in Seattle?
SEATTLE’S LOWRISE MULTIFAMILY ZONES THIS ZONING CHART IS FOR ILLUSTRATIVE PURPOSES ONLY General standards are shown. Please refer to the Land Use Code for exceptions and specific regulations.
What is LR3 zoning?
LR3 is the densest of the Lowrise zones and is generally present in urban villages and centers, near frequent transit, and in popular growing neighborhoods like Capitol Hill and Ballard. Here’s a map of all the low-rise zones.