How do you give Geodon?
Dose Selection GEODON Capsules should be administered at an initial daily dose of 20 mg twice daily with food. In some patients, daily dosage may subsequently be adjusted on the basis of individual clinical status up to 80 mg twice daily.
What is the medical use of Hetastarch?
Hetastarch is used to treat or prevent hypovolemia (decreased blood plasma volume, also called “shock”) that may occur as a result of serious injury, surgery, severe blood loss, burns, or other trauma. Hetastarch may also be used for purposes not listed in this medication guide.
How do you mix olanzapine injections?
Directions for Preparation of Olanzapine for Injection with Sterile Water for Injection — Dissolve the contents of the vial using 2.1 mL of Sterile Water for Injection to provide a solution containing approximately 5 mg/mL of olanzapine. The resulting solution should appear clear and yellow.
Can you reconstitute Zyprexa with normal saline?
Instructions for use/handling – ZYPREXA IM vial ZYPREXA IM should be reconstituted only with sterile water for injection.
Can ziprasidone be given IV?
Ziprasidone intramuscular is intended for intramuscular use only and should not be administered intravenously. GEODON for Injection (ziprasidone mesylate) should only be administered by intramuscular injection and should not be administered intravenously.
How do you reconstitute ziprasidone?
Ziprasidone for injection is reconstituted by adding 1.2 mL of Sterile Water for Injection to the vial and shaking vigorously until the entire drug is dissolved.
How do you give hespan?
How is Hespan given? Hespan is injected into a vein through an IV. A healthcare provider will give you this injection. Your breathing, blood pressure, oxygen levels, kidney function, and other vital signs will be watched closely while you are receiving Hespan.
When do you use hespan?
1 INDICATIONS AND USAGE HESPAN® is indicated in the treatment of hypovolemia when plasma volume expansion is desired in settings where adequate alternative treatment is unavailable. It is not a substitute for blood or plasma.
Can you give olanzapine IV?
Similar to haloperidol, olanzapine can be used safely via the IV route despite both being FDA-approved for intramuscular (IM) administration only.
Can normal saline be used as water for injection?
Do NOT use 0.9% sodium chloride in place of sterile water for injection (unless directed in the prescribing information) to reconstitute medications, which can result in hyperosmotic solutions at or near the saturation point and cause crystallization or infusion site reactions.
How many ml of diluent should be added?
How much initial sample and diluent should you use? Answer: 1:5 dilution = 1/5 dilution = 1 part sample and 4 parts diluent in a total of 5 parts. If you need 10 ml, final volume, then you need 1/5 of 10 ml = 2 ml sample. To bring this 2 ml sample up to a total volume of 10 ml, you must add 10 ml – 2 ml = 8 ml diluent.
Which antipsychotics can be given intravenously?
Haloperidol, as the only antipsychotic that can be administered intravenously, is the most used and studied antipsychotic drug for delirium treatment. It has a relatively short time of peak plasma concentration (iv: 5-15 minutes), and it is useful for its sedative effects rather than the specific anti-delirium one.
Can you push Geodon IV?
GEODON for Injection (ziprasidone mesylate) should only be administered by intramuscular injection and should not be administered intravenously.
Can Geodon be given IV?
GEODON for Injection (ziprasidone mesylate) should only be administered by intramuscular injection and should not be administered intravenously. Single-dose vials require reconstitution prior to administration. Add 1.2 mL of Sterile Water for Injection to the vial and shake vigorously until all the drug is dissolved.
What do you reconstitute Geodon with?
Powdered ziprasidone is provided in a glass vial and reconstituted with 1.2 mL of sterile water. One milliliter of the solution (20 mg) is typically given intramuscularly as the recommended dose. An instructional card originally provided states that reconstitution is achieved after 1 minute of vigorous shaking.
Is hespan the same as Hetastarch?
Hetastarch is used to treat low blood volume (hypovolemia) and to remove leukocytes from drawn blood (leukapheresis). Hetastarch is available under the following different brand names: Hespan and Hextend.
How do you administer a hespan?
HESPAN® is administered by intravenous infusion only. Total dosage and rate of infusion depend upon the amount of blood or plasma lost and the resultant hemoconcentration. The amount usually administered is 500 to 1000 mL.
How fast can you push Haldol IV?
Neurology and psychiatry consultations were sought. The psychiatry team recommended haloperidol administered via intravenous (IV) push 5 mg every 20 minutes until sedation was achieved, so that the neurologist and psychiatrist could evaluate the patient.
What is the maximum rate of theophylline infusion?
Maximum rate: 0.36 mg/kg/minute, and no greater than 25 mg/minute. I.M. administration is not recommended. DOSAGE AND ADMINISTRATION General Considerations: The steady-state serum theophylline concentration is a function of the infusion rate and the rate of theophylline clearance in the individual patient.
What are the results of Hespan infusion?
Intravenous infusion of Hespan® results in expansion of plasma volume. Hespan® results in expansion of plasma volume that decreases over the succeeding 24 to 36 hours. The degree of plasma volume expansion and improvement in hemodynamic state depend upon the patient’s intravascular status.
How much Hespan do you give for leukapheresis?
Hespan Dosage and Administration 1 Adults. The amount usually administered is 500 to 1000 mL. 2 Leukapheresis. The Hespan® and citrate should be thoroughly mixed to assure effective anticoagulation of blood as it flows through the leukapheresis machine. 3 Direction for use for Hespan®. Do not use plastic container in series connection.
How is aminophylline administered intravenously?
Intravenous administration of aminophylline occurs via two methods. First, a loading dose is given to achieve a serum concentration of 10 mcg/ml. Then, the constant maintenance infusion follows once the serum concentration has reached 10 to 15 mcg/ml.