What are the types of sensors used for interfacing in 8051?
PIR sensors are widely used in motion detecting devices. This article is about interfacing a PIR sensor to 8051 microcontroller. A practical intruder alarm system using PIR sensor and 8051 microcontroller is also included at the end of this article.
Which transistor is used in IR sensor?
IR Sensor Circuit using Transistor This circuit is mainly used for obstacle detection using an IR LED. So, this circuit can be built with two transistors like NPN and PNP. For NPN, BC547 transistor is used whereas, for PNP, BC557 transistor is used. The pinout of these transistors is the same.
What is the input of IR sensor?
What is the Input Power of the IR Sensor? The IR proximity Sensor module can be powered by both 3.3V and 5V supplies. This enables the module to be used in both 5V systems like Arduino and 3.3V systems like raspberry pi.
Which device is used as motion sensor in microcontroller?
PIR (Passive Infrared) or Motion Sensor is used to detect the motion of moving human body or objects. Whenever someone comes in the range of PIR sensor, it gives High at its output pin. We have previously interfaced PIR with other Microcontrollers: Arduino Motion Detector using PIR Sensor.
What is sensor interfacing?
Sensor interfacing is a mix of amplification, filtering, and other signal conditioning as well as analog-to-digital conversion. The analog-to-digital converter (ADC) may be in your microcontroller, but you will still need to make the sensor compatible with the ADC input.
What is meant by interfacing in 8051?
Microcontroller 8051 Peripheral devices. Interfacing is the process of connecting devices together so that they can exchange the information and that proves to be easier to write the programs.
How do IR sensor works?
Active infrared sensors both emit and detect infrared radiation. Active IR sensors have two parts: a light emitting diode (LED) and a receiver. When an object comes close to the sensor, the infrared light from the LED reflects off of the object and is detected by the receiver.
How many pins are present in the IR sensor?
2. How many pins are present in the IR Sensor? Explanation: The pins that are present on the IR Sensor include, the Ground, the Vcc and the Signal pins. The role of the Ground and the Vcc is to power the sensor.
How do sensors connect to microcontroller?
However, the sensors can have their own ADCs that are optimized to the resolution of the sensor data and assist with minimizing the power consumption of the node. These can then be interfaced to the microcontroller via a serial UART or general-purpose I/O pins, or through an I²C two-wire interface.
What is interfacing in microcontroller?
Microcontroller Interfaces. An interface is the circuitry that connects an embedded controller to the outside world. Initially, all I/O in early micros was just the parallel data and address buses extended to accommodate additional I/O circuitry.
What is the basic concept of interfacing?
The interfacing process includes some key factors to match with the memory requirements and microprocessor signals. The interfacing circuit therefore should be designed in such a way that it matches the memory signal requirements with the signals of the microprocessor.
What is output of IR sensor?
IR detectors are digital out – either they detect 38KHz IR signal and output low (0V) or they do not detect any and output high (5V).
What are the components in IR sensor?
Active IR sensors have two parts: a light emitting diode (LED) and a receiver. When an object comes close to the sensor, the infrared light from the LED reflects off of the object and is detected by the receiver.
What is PIR sensor interfacing with 8051?
In this tutorial, we are going to discuss PIR sensor interfacing with 8051. This sensor will detect motion in the room, automatic door in the elevator, automatic lighting system, and washroom amenities. Before starting this tutorial we should know the below topics.
What are the protocols used in 8051 IR remote control interface?
NEC IR Remote Control Interface with 8051 IR Remote Controllers and receivers follow standard protocols for sending and receiving the data. Some of the standard protocols are NEC , JVC , SIRC (Sony Infrared Remote Control) etc.
How does the infrared obstacle sensor work?
The sensor has a very good and stable response even in ambient light or in complete darkness. An IR sensor consists of an IR LED and an IR Photodiode; together they are called as Photo–Coupler or Opto–Coupler. As said before, the Infrared Obstacle Sensor has a built-in IR transmitter and IR receiver.
What are the components of IR sensor?
An IR sensor consists of an IR LED and an IR Photodiode; together they are called as Photo–Coupler or Opto–Coupler. As said before, the Infrared Obstacle Sensor has a built-in IR transmitter and IR receiver.